Scuba diving

BREATHING UNDERWATER:D
Water normally contains dissolved oxygen from which fish and other aquatic animals extract all their required oxygen as the water flows past their gills. Humans lack gills and do not otherwise have the capacity to breathe underwater unaided by external devices.[3] Although the feasibility of filling and artificially ventilating the lungs with a dedicated liquid (Liquid breathing) has been established for some time,[6] the size and complexity of the equipment allows only for medical applications with current technology.[7]
Early diving experimenters quickly discovered it is not enough simply to supply air in order to breathe comfortably underwater. As one descends, in addition to the normal atmospheric pressure, water exerts increasing pressure on the chest and lungs—approximately 1 bar or 14.7 psi for every 33 feet or 10 meters of depth—so the pressure of the inhaled breath must almost exactly counter the surrounding or ambient pressure to inflate the lungs. It generally becomes difficult to breathe through a tube past three feet under the water.[3]
By always providing the breathing gas at ambient pressure, modern demand valve regulators ensure the diver can inhale and exhale naturally and virtually effortlessly, regardless of depth.
Because the diver's nose and eyes are covered by a diving mask; the diver cannot breathe in through the nose, except when wearing a full face diving mask. However, inhaling from a regulator's mouthpiece becomes second nature very quickly.

Open-circuit
The most commonly used scuba set today is the "single-hose" open circuit 2-stage diving regulator, coupled to a single pressurized gas cylinder, with the first stage on the cylinder and the second stage at the mouthpiece.[2] This arrangement differs from Emile Gagnan's and Jacques Cousteau's original 1942 "twin-hose" design, known as the Aqua-lung, in which the cylinder's pressure was reduced to ambient pressure in one or two or three stages which were all on the cylinder. The "single-hose" system has significant advantages over the original system.
In the "single-hose" two-stage design, the first stage regulator reduces the cylinder pressure of about 200 bar (3000 psi) to an intermediate level of about 10 bar (145 psi) The second stage demand valve regulator, connected via a low pressure hose to the first stage, delivers the breathing gas at the correct ambient pressure to the diver's mouth and lungs. The diver's exhaled gases are exhausted directly to the environment as waste. The first stage typically has at least one outlet delivering breathing gas at unreduced tank pressure. This is connected to the diver's pressure gauge or computer, in order to show how much breathing gas remains.

Rebreather

An Inspiration electronic fully closed circuit rebreather
Main article: Rebreathers
Less common are closed and semi-closed rebreathers,[8] which unlike open-circuit sets that vent off all exhaled gases, reprocess each exhaled breath for re-use by removing the carbon dioxide buildup and replacing the oxygen used by the diver.
Rebreathers release few or no gas bubbles into the water, and use much less oxygen per hour because exhaled oxygen is recovered; this has advantages for research, military[2], photography, and other applications. The first modern rebreather was the MK-19 that was developed at S-Tron by Ralph Osterhout that was the first electronic system.[citation needed] Rebreathers are more complex and more expensive than sport open-circuit scuba, and need special training and maintenance to be safely used.[8]
Because the nitrogen in the system is kept to a minimum, decompressing is much less complicated than traditional open-circuit scuba systems and, as a result, divers can stay down longer. Because rebreathers produce very few bubbles, they do not disturb marine life or make a diver’s presence known; this is useful for underwater photography, and for covert work.

Gas mixtures



Nitrox cylinder marked up for use
Main article: Breathing gas
For some diving, gas mixtures other than normal atmospheric air (21% oxygen, 78% nitrogen, 1% trace gases) can be used,[2][3] so long as the diver is properly trained in their use. The most commonly used mixture is Enriched Air Nitrox, which is air with extra oxygen, often with 32% or 36% oxygen, and thus less nitrogen, reducing the likelihood of decompression sickness. The reduced nitrogen may also allow for no or less decompression stop times and a shorter surface interval between dives. A common misconception is that nitrox can reduce narcosis, but research has shown that oxygen is also narcotic.[9][10]
Several other common gas mixtures are in use, and all need specialized training. The increased oxygen levels in nitrox help fend off decompression sickness; however, below the maximum operating depth of the mixture, the increased partial pressure of oxygen can lead to oxygen toxicity. To displace nitrogen without the increased oxygen concentration, other diluents can be used, often helium, when the resultant mixture is called trimix.
For technical dives, some of the cylinders may contain different gas mixture for each phase of the dive, typically designated as Travel, Bottom, and Decompression. These different gas mixtures may be used to extend bottom time, reduce inert gas narcotic effects, and reduce decompression times.

www.xinmsn.com